Please select To the mobile version | Continue to access the desktop computer version
12345
Back New
Author: wookielover

Box Mod / Box battery advice

[Copy link]

11610K

Threads

12810K

Posts

37310K

Credits

Administrators

Rank: 9Rank: 9Rank: 9

Credits
3732793
26-11-2019 20:55:16 Mobile | Show all posts
Another slight niggle with mine, i have noticed it has just started making a very light 'hissing' kind of noise when fired; just as the button is pressed but before the tank starts to make its noise. I think this may be rattlesnaking? Not sure
Reply Support Not support

Use magic Report

11610K

Threads

12810K

Posts

37310K

Credits

Administrators

Rank: 9Rank: 9Rank: 9

Credits
3732793
26-11-2019 20:55:17 Mobile | Show all posts
I've not noticed that with mine. My Zmax used to rattlesnake but only after being fired, not before. Does it do it in both PWM and DC-DC modes?
Reply Support Not support

Use magic Report

11610K

Threads

12810K

Posts

37310K

Credits

Administrators

Rank: 9Rank: 9Rank: 9

Credits
3732793
26-11-2019 20:55:18 Mobile | Show all posts
Only when in PWM mode, is there any harm in me keeping it in DC-DC mode?  I still dont fully know the difference
Reply Support Not support

Use magic Report

11610K

Threads

12810K

Posts

37310K

Credits

Administrators

Rank: 9Rank: 9Rank: 9

Credits
3732793
26-11-2019 20:55:19 Mobile | Show all posts
I'll be honest, neither do I really. The only thing I noticed is with a 1.4/5 ohm coil it's better in PWM but with a 1.7/8 ohm it's better in DC-DC.

Mostly it's been in PWM this week but if I fancy a stronger hit I switch to DC-DC.
Reply Support Not support

Use magic Report

11610K

Threads

12810K

Posts

37310K

Credits

Administrators

Rank: 9Rank: 9Rank: 9

Credits
3732793
26-11-2019 20:55:20 Mobile | Show all posts
The chip in the sigelei 30w cannot give out lower than the battery voltage so it needs to pulse the voltage to give an effectively average lower output to match the selected wattage and coil resistance, this is known as PWM (pulse width modulation). This can result in a rattlesnake/rasping effect.

In DC-DC mode, it is a flat signal (no pulsing and no rattlesnaking) but can only be output at or higher than the battery voltage.

However, if you have PWM mode selected, as soon as the required voltage is above the battery voltage, it will automatically become a boosted DC output. So you only get PWM when required voltage is below battery voltage.

If you have DC-DC mode you will not be able to get a voltage below the battery voltage, no matter what the display says.

Described well below. It's a different device but the same chip. Watch from 23:46 for the relevant part.
Reply Support Not support

Use magic Report

11610K

Threads

12810K

Posts

37310K

Credits

Administrators

Rank: 9Rank: 9Rank: 9

Credits
3732793
26-11-2019 20:55:20 Mobile | Show all posts
Thanks for that Stuart, i returned mine today as the noise when in pwm was really annoying. My friend has also just got the same mod and his dosent do it.
Reply Support Not support

Use magic Report

11610K

Threads

12810K

Posts

37310K

Credits

Administrators

Rank: 9Rank: 9Rank: 9

Credits
3732793
26-11-2019 20:55:21 Mobile | Show all posts
Another thanks, I had a look for IPV mini reviews as it's basically the same as the Sigelei and the PB one didn't pop up. Certainly gives a bit more info on how the chip performs, cheers.
Reply Support Not support

Use magic Report

12345
Back New
You have to log in before you can reply Login | register

Points Rules

返回顶部